Thursday, 8 June 2017

the middle path mantra

Pin It now!
Tatting over tails is a common method of hiding ends when we start a project or when we add new thread.
Continuing from the previous post where stepwise and comparative visuals demonstrated where to leave off the tail when hiding it within double stitches.
Part 2 demonstrates the same principle but in case of directional tatting, when we are working stitches from backside – where half stitches are in reverse order or sequence.

Since tail was hidden in a ring in Part 1, this time we show it on a chain.

RW – reverse work
DS – double stitch ;
FHS – first half stitch ;
SHS – second half stitch.
RODS – reverse order DS, where sequence of half stitches is reversed. 


Tatting over Tails
Part 2 - backside 

This time I chose to tat a chain, working from the backside with RODS (reverse order of stitch). Here, SHS is made first, then FHS
1RODS = (1SHS,1FHS)

RW after ring made previously. We are now working from the back/wrong side.

1. Joining new thread (green/blue).

2. Start chain. 2 stitches (RODS) already made, encapsulating the tail.
Starting the 3rd stitch with a SHS.
Notice the position of tail – it lies to the ‘front’ of the stitch being formed.

3. SHS snugged

4. FHS being made. Notice position of tail – it tends to lie ‘behind’ the half stitch

5. FHS snugged.
3 RODS completed

6. Continue till 4 RODS and 1 SHS made. Then leave tail and tat 1FHS normally.

7. Continue chain - more stitches made after leaving the tail
This is how it looks from the backside of work

8. View from the frontside of work

9. Snip the extra tail lengths as close to work as possible. Arrows show where each tail was snipped
NOTE : It is advisable to defer this step till a few more elements have been worked. Then pull the tails one last time and snip.

10. Tatting over tails frontside for ring and backside for chain, and leaving the tail in middle of a stitch, completed. 

So, here is the simple mantra to remember ...

the  middle path mantra
leave tail in the middle of a stitch !

Stop tatting over tail between 1st & 2nd half stitch when tatting a double stitch 
(frontside tatting);
Stop tatting over tail between 2nd & 1st stitch when working a reverse order double stitch (backside tatting).

This mantra also holds true for the reverse stitch (unflipped),  
as in 2nd side of a split ring or direct tatting.

♡♡♡♡♡♡♡♡♡♡♡♡♡♡♡♡♡♡♡




happy tatting always J

8 comments:

  1. I don't do fs/bs tatting, but this is interesting anyway. I'm interested that you cut the thread after a few more stitches. I cut the thread after the half stitch and then make sure the next half covers over the end.

    ReplyDelete
  2. I do what Jane does a above and some times I pull the stitches down towards the start with extra tention snip and then loosen tention so that snippet is covered completely inside.

    ReplyDelete
  3. I cut off any threads when I have finished the round or motif.

    ReplyDelete
  4. Like Jane, I don't do FS/BS tatting but I do tat over tails and join thread similar to the way you do it. I do the middle path sometimes. I must admit I am not consistent where I stop hiding. Thanks again for a great post.

    ReplyDelete
  5. Thank you so much everybody for sharing your own processes :-)

    Jane, I am always paranoid that the tail may slip away, hence wait till a few more elements are tatted, before I snip it off. But will give your way a try.

    Ah, another good tip, Carollyn.

    I also generally do the same, Margaret. In case the tatting has to join back at the exact same point later, I prefer to leave the tails hanging. Otherwise I snip them off after a couple of elements.

    Tatting over tails reduces half the ends one needs to take care of later, so I'm always game, Bernice ;-D

    ReplyDelete
  6. Hi Blogger,
    Blogs are competing for awards in 2017.
    A total of $30,000 cash prize-winning inter-blog competition has started. You have a great blog! So join you now. We will be honored to welcome you to this beautiful web-activity, which will be awarded to many bloggers. You are invited to the blog writers competition for May-June 2017. You have absolutely visited to get detailed information and to apply.

    Web : http://www.bloggercontest.com
    Mail : contact@bloggercontest.com
    Pbx : +441012950166

    ReplyDelete
  7. Excellent photographs and instructions! Thanks for this great tutorial. (Pretty thread, too!)

    ReplyDelete
    Replies
    1. I'm thrilled that you like it, Marilee :-)
      The thread (from a set of 5 different variegates) is excellent, but too thick for normal tatting - a size 3 probably. A sorry substitute for your hand-dyed skeins ;-D

      Delete